1: 2012-09-22 (土) 22:12:08 iseki  |
現: 2012-09-25 (火) 14:17:13 iseki |
| | [[Back to Setting Menu>../../Setting Menu]] | | [[Back to Setting Menu>../../Setting Menu]] |
| - | ** Motion (for Kinect SDK) [#i17804a1] | + | *** Motion (for Kinect SDK) [#i17804a1] |
| - | &ref(../Setting_Motion_Kinect_en.png); | + | &ref(../Setting_Motion_kinect_en.png); |
| | + | #br |
| | | | |
| - | **** Mirroring [#na527ba8] | + | **** Joint Constraint [#j3827fe3] |
| - | - Mirroring of Kinect Data is performed. | + | - Restrictions are given and corrected to a motion of a joint and a gradual vibration of hand and foot etc. |
| - | - An avatar motion is mirrored, too. | + | - But this is under experimental. |
| | + | #br |
| | | | |
| - | **** Use Camera Image [#d3b90e25] | + | **** Smoothing [#odbc7896] |
| - | - Display camera image on Sensor Window. | + | - ''Smoothing of Kinect SDK'' |
| - | - If it is unchecked, background of Sensor Window is light gray. | + | -- A motion of joint is smoothed using the function of ''Kinect SDK''. |
| | + | -- It seems that the Moving Average is probably used. But detailed parameters are unknown. |
| | + | -- It is referring to the manual of ''Kinect SDK'' for details (if it exists). |
| | + | - ''Moving Average Smoothing'' (our implementation) |
| | + | -- This uses typical ''Moving Average'' to smoothing move of joints. |
| | + | #br |
| | | | |
| - | *** Setting of Log Window Dialog [#m11bf759] | + | **** Correction [#v1e1fcf4] |
| - | &ref(DIALOG_LOG2_E.jpg); | + | - ''Rotation of Y-Axis'' |
| | + | -- This rectifies the inclination of avatar's front and back. A unit is a degree. |
| | + | #br |
| | | | |
| - | **** Position [#a01e22b1] | + | **** Detection of Parts [#od01da3d] |
| - | - Display position data (XYZ) from Kinect. | + | - ''ALL'' |
| - | | + | -- The whole body is detected. |
| - | **** Rotation Matrix [#i839a39a] | + | - ''UPPER'' |
| - | - Display elements of rotation matrix from Kinect. | + | -- The upper body is detected. |
| - | | + | |
| - | **** Quaternion [#efa9fa10] | + | |
| - | - Display relative Quaternion that is computed from rotation matrix. | + | |
| - | - Viewer reads this data directory from shared memory. | + | |
| - | | + | |
| - | **** Received Data from Network [#n805e0c7] | + | |
| - | - Display received Animatin UUID, Number of joints and Unit Data Size (double[8] or float[4]) | + | |
| - | **** Network Check [#je622a03] | + | |
| - | - The information for debugging for network functions is displayed. So, receiving Rate in every 5s (packets/s), delay time of own data, received Animation Num. and Connection Key are displayed. | + | |
| - | | + | |
| - | *** Setting of Data Save Dialog [#x7e58104] | + | |
| - | &ref(DIALOG_DATA_E.jpg); | + | |
| - | - Not implemented yet. This function will be supported by v2.1.0. | + | |
| - | | + | |
| - | *** Setting of Network Dialog [#x9904c0e] | + | |
| - | &ref(DIALOG_NETWORK3_E.jpg); | + | |
| - | | + | |
| - | **** Output of Data [#i3397729] | + | |
| - | - Network and Local: Animation Data is wrote to shared memory and sent to Animation Relay Server. | + | |
| - | - Network only: Animation data is sent only to Animation Relay Server. | + | |
| - | **** Fast Transfer Mode [#k875fd78] | + | |
| - | - Usually, the UDP data for one frame of an avatar is a header(64Byte) + elements number of joint data(8) x double(8Bytes) x joints number(11) = 768Bytes. | + | |
| - | - If this is checked, a data type will turn into a float(4Bytes), and will serve as 416Bytes in all. In this size, fragmentation is never caused on the network. | + | |
| - | - You can change this, also in during transmission of data. | + | |
| - | | + | |
| - | **** Received Port [#bbceb756] | + | |
| - | - Port number of UDP which receives data from an Animation Relay Server. | + | |
| - | - Usually, 8200 is used in the default . | + | |
| - | - If your PC is in NAT (correctly NAPT), you must to set up a router, and UDP data must be forwarded from Port of Router (same number as Received Port) to Received Port of PC which executing SLKinect2. (default is from Router:8200 to PC:8200) | + | |
| - | - You cannot change this item during login. | + | |
| - | | + | |
| - | **** Animation Relay Server [#v1b7ba57] | + | |
| - | - IP address or FQDN of an Animation Relay Server is specified. | + | |
| - | - You cannot change this item during login. | + | |
| - | - Our test server is ''silver-star.nsl.tuis.ac.jp''. You can use this server, but support is nothing. | + | |
| - | | + | |
| - | **** Port Num. [#jdbefcf8] | + | |
| - | - The UDP port number of an Animation Relay Server. | + | |
| - | - It asks administrator and sets to a server. | + | |
| - | - Usually, 8200 should be used in the default. | + | |
| - | - You cannot change this item during login. | + | |
| - | - Port number of ''silver-star.nsl.tuis.ac.jp'' is 8200. | + | |
| - | | + | |
| - | **** Group Key [#lf77f9dd] | + | |
| - | - This key is for grouping of user on an Animation Relay Server. A top string (Group Key Prefix) can be specified by the server side. | + | |
| - | - It cannot log in, unless Group Key Prefix is the same as one on server side. | + | |
| - | - About Group Key Prefix, please ask server administrator. | + | |
| - | - It can set up freely except a Group Key Prefix. However, the character must be only an alphanumeric character and must be less than 16 characters on the whole including a Group Key Prefix. | + | |
| - | - You cannot change this item during login. | + | |
| - | - Group Key Prefix of ''silver-star.nsl.tuis.ac.jp'' is ''NSL_'' | + | |
| | #br | | #br |
